General Purpose Hose 20 Bar

General Purpose Hose 20 Bar is a versatile industrial rubber hose described for industrial and agricultural service, compressor lines, hot-air and water transfer, low-pressure spraying and light chemical handling. Its published construction includes an EPDM tube and cover, high-tensile synthetic-yarn reinforcement, a temperature range of -30°C to +100°C and a 3:1 safety factor. Suitability must still be checked against the actual medium and operating conditions.

General Purpose Industrial Hose Supply in Malaysia

Advtech Engineering supplies flexible hoses, couplings and fittings for industrial requirements in Malaysia. This general-purpose hose can be considered where one hose specification is being reviewed for several routine plant or equipment services. “General purpose” does not mean universal compatibility; each duty should be identified before selection or assembly.

Published Product Construction

Typical Applications Listed for This Hose

• General industrial and agricultural service
• Compressor lines, subject to the conveyed medium and equipment requirements
• Hot-air and water transfer within the confirmed operating limits
• Low-pressure spraying
• Light chemical handling after media-compatibility verification

Actual performance depends on hose size, pressure, temperature, fluid, flow, fittings, routing and service frequency. Do not extend these general examples to steam, aggressive chemicals, fuel, oil, food, breathing air or another critical service without specific supporting data.

Understanding the 20 Bar Product Designation

“20 Bar” is part of the published product designation. The allowable working pressure of a complete hose assembly can be affected by hose size, temperature, media, fittings, attachment method, bend condition, wear and pressure surges. Confirm the rated limit of every component and the assembled hose before operation.

Media and Temperature Compatibility

State whether the hose will carry air, water, spray solution or a light chemical. For a chemical mixture or trade-name product, provide its Safety Data Sheet (SDS), concentration and temperature. The published range of -30°C to +100°C does not establish compatibility with every fluid throughout that entire range, and it should not be interpreted as a steam rating.

Anti-Static Wire Configuration Must Be Confirmed

The existing product information contains two descriptions: it mentions an optional anti-static copper wire and also states that the reinforcement is integrated with a stainless-steel anti-static wire. Confirm the exact wire material and supplied configuration in the quotation. Where static control is required, also specify the bonding, grounding and continuity-testing procedure for the complete assembly.

Information Needed for Selection and Quotation

• Transferred medium and SDS where applicable
• Normal and maximum working pressure, including surges
• Fluid and ambient temperature
• Required hose inside diameter and length
• Flow rate and frequency of use
• Fitting type, size, thread or flange details and material
• Whether a loose hose or completed assembly is required
• Routing, bend, movement, abrasion and outdoor exposure
• Static-control and testing requirements, if any
• Quantity and required supporting documentation

End Connections and Hose Assembly Review

End connections should be selected for the hose, medium, pressure and mating equipment. Confirm connection standard, size, sealing method, fitting material and attachment method before production. Advtech Engineering provides hose assembly and fabrication support for requirements reviewed using the buyer’s operating information.

Installation and Routing Considerations

Install the hose without twisting, crushing, excessive tension or bends tighter than the applicable recommendation. Provide enough length for normal movement while avoiding loose loops that can be snagged or driven over. Protect the hose from sharp edges, hot surfaces, traffic and avoidable abrasion, and support the assembly where its weight could load the fittings.

Inspection and Preventive Replacement

Before use, inspect the cover, markings, fittings and attachment zones for cuts, cracking, blistering, softening, abrasion, leakage, corrosion or connection movement. Isolate and depressurise the system before inspection, adjustment or replacement. Remove a damaged or questionable assembly from service; replacement intervals should reflect the operating severity and inspection findings.

Frequently Asked Questions

Can this hose be used for any chemical?

No. The published description mentions light chemical handling, but compatibility depends on the exact chemical, concentration, temperature, pressure and exposure. Provide the SDS for review.

Is General Purpose Hose 20 Bar suitable for steam?

The available product information does not state a steam rating. The published -30°C to +100°C range should not be used as evidence of steam suitability.

Is the anti-static wire copper or stainless steel?

The existing data contains both descriptions. Confirm the exact wire material and whether it is included in the specific hose being quoted. If continuity is required, verify the finished assembly according to the applicable procedure.

Need a General Purpose Hose 20 Bar quotation in Malaysia? Contact Advtech Engineering with the medium, pressure, temperature, hose size, length, end connections and quantity. You may also browse the related industrial and chemical hose category.

Safety note: Selection, assembly, installation, testing and use should be completed by competent personnel using current manufacturer information, applicable rules and the site’s risk assessment. Confirm suitability for the actual service before operation.